K-GA44Q FUEL DISPENSER

K-GA44Q FUEL DISPENSER

FlowMeter Type :Optional

Accuracy ±0.2%

Pressure Loss (kg/cm): Under 0.25

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display: Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price :0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight :280kg

Dimension(L×W×H) : 1540*690*2210(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 29

oil, so as to reduce the volume of drained oil. Turn adjusting bolt clockwise to reduce discharge, anticlockwise to i fuel dispenser ncrease discharge. Therefore, changing the position of bolt enable discharge approach academic volume and reach the requirements on measurement transducer of national appraisal regulations. As two regulative bolts access to adjusting piston, the adjusting discharge in a circulation per bolt can be calculated in the following formula: △V = 1/2πd12 nt (2--4 ) △V ── adjusting value in per circulation; D1 ── diameter of regulative piston; n ── turning number of adjusting bolt; t ── screw- pitch of adjusting bolt. There is another metal piston measurement transducer in current market. See the Diagram 2-19. Regulative piston is singularly fuel dispenser installed in piston rather than connect with rod in this model. Its adjusting value in terms of per adjusting bolt is: △V = 1/4πd2 nt (2--5 ) Common failure and Troubleshooting Metal piston measurement transducer has the two common failures --- accuracy decline and mechanical trouble. Measure accuracy beyond scope The allowed measurement accuracy of fuel dispenser is ±0.3 %, repeated tolerance no more than 0.15 % according to the stipulation of JJG443-98 Fuel dispenser. The maximum allowed tolerance of min. measured valve don’t exceed ±0.5 %，its repeated tolerance no more than 0.25 %. The ratio of maximum flow (Q max.) to minimum fuel dispenser flow (Q min.) is 10 to 1. as fuel dispenser leave factory. The ratio should not be less than 5: 1 in inspecting at operation locale. All of exceeded tolerance is regarded as beyond measurement accuracy. There are many elements and reasons resulting in measurement accuracy beyond scope, including unstable hydraulic system (extensive pressure fluctuation), electric system failure, thick colloid in frictional interface, measurement transducer abrasion, etc. The last two reasons will mainly be introduced in this article. Regulating adjusting

application controls　　which peripheral is not anymore important provided that the access to the peripherals is gra fuel dispenser nted through a　　standard interface.　　The following scheme shows the referred architecture framework:　　 Cashier display　　 IFSF　　 Site server　　 (XML)　　 Barcode scanner Device Proxy　　 SELL application　　 MSR IFSF　　 (XML)　　 Pin-Pad　　 fuel dispenser POS　　 XML proprietary　　 ICC readwrite　　 IFSF EPSPOS　　 (XML)　　 Printer　　 UPOS +　　 IFSF add-on　　 EPS client EPS server　　 EPS　　 fuel dispenser IFSFISO8583-oil　　 (Remote) Switch　　 Authorisation Centres　　Device Proxy and Peripherals management　　UPOS is the standard for managing peripherals. The device proxy provides an XML simple command　　interface and executes commands through UPOS control of peripherals; this

printer terminated its contract, apparently on government orders, the paper had to start printing in Smolensk. It ca fuel dispenser nnot be sold in public kiosks or distributed by the state-run subscription system; it has been subjected to enormous fines. Then, this week, the Russian printer backed out too. On television, Mr Lukashenka forwent his campaign broadcast; a conspiracy-theory documentary about recent revolutions was shown instead. But his activities are given interminable, adulatory exposure. That is one difference with Ukraine, where Mr Yushchenko enjoyed at least some favourable coverage. Another is the more certain prospect, in Belarus, of violence. There was a foretaste of this on March 2nd, when Alyaksandr Kozulin, another opposition candidate (learning from Ukraine, most opposition factio fuel dispenser ns have united behind Mr Milinkevic), was assaulted, along with several supporters and journalists (the police shot the tyres of a car carrying some of them). One of his assailants was Dmitry Pavlichenko, the head of a special security service that is accused by Mr Kozulin and others of organising the disappearances. Mr Pavlichenko also directed the riot police who tried to obstruct the snowy opposition rally. “They threw me on the floor and kicked me,�said Mr Kozulin, as he registered his injuries at a hospital. Inside the police station, he smashed a portrait of the president, defiance for which he may now face criminal charges. “If a candidate for fuel dispenser president is arrested and beaten,�comments Mr Milinkevic, “there won t even be the imitation of an election.� Television portrayed the incident as a provocation staged with the connivance of foreign journalists. To a politician like Mr Lukashenka, all this counts as legitimate campaigning. Another mark of his Soviet mindset is that only an overwhelming victory will do. A fraud-facilitating system of early voting, plus one-sided electoral commissions, should ensure that he gets one. “He s lost touch with reality,�observes Mr Lebedko, t